Cisco CCNA Certification Exam Tutorial: Configuring Dialer Profiles

By:Chris Bryant, CCIE #12933

The most common method of configuring ISDN is with dialer maps, but dial information can also be configured on a logical interface. To pass the CCNA exam, you must know how to configure and troubleshoot both dialer maps and dialer profiles.

Dialer Profiles allow different dialing information to be configured onto logical interfaces. The logical interfaces may have different dialing destinations, different remote router names, etc., but they’ll be using the same physical interface.

Dialer strings are used on dialer profiles. Note that each logical interface has a different IP address, a different remote router to dial, and a different dialer string, but they will be using the same physical interface to dial out. The commands dialer pool and dialer pool-member are used to link the logical and physical interfaces. The number following each command must match for the logical interface to correctly bind to the physical interface.

R1(config)#interface dialer0

R1(config-if)#ip address 172.16.1.1 255.255.255.0

R1(config-if)#encapsulation ppp

<. The encapsulation type is placed on both the logical and physical interfaces. >

R1(config-if)#dialer remote-name Remote0

R1(config-if)#dialer pool 1

< places logical interface into dialer pool >

R1(config-if)#dialer string 5551212

< number dialed to contact router Remote0 >

R1(config-if)#dialer-group 1

< links logical interface to dialer-list 1 >

R1(config)#interface dialer1

R1(config-if)#ip address 172.16.1.2 255.255.255.0

R1(config-if)#encapsulation ppp

R1(config-if)#dialer remote-name Remote1

R1(config-if)#dialer pool 1

R1(config-if)#dialer string 5551234

R1(config-if)#dialer-group 1

R1(config)#interface bri0

R1(config-if)#no ip address

< With dialer profiles, IP addresses are assigned to logical interfaces. >

R1(config-if)#encapsulation ppp

< The encapsulation type is place on both the logical and physical interfaces.>

R1(config-if)#dialer pool-member 1

< The number associated with this command should match the number configured with the dialer pool number on the logical dialer interfaces. >

R1(config-if)#isdn spid1 0835866101

R1(config-if)#isdn spid2 0835866301

When configuring dialer profiles, the encapsulation type should be placed on both the physical BRI interface and the logical dialer interfaces. The SPIDs are configured on the physical interface as well.

Configuring dialer profiles can be a little tricky at first, and the best way to master this skill is to get real hands-on practice in your own CCNA / CCNP home lab or a rack rental service. Either way, hands-on is the best practice. Best of luck in your CCNA studies!

Digg del.icio.us Blink Stumble Spurl Reddit Netscape Furl

Article keywords: cisco, ccna, certification, pass, exam, isdn, dialer, profile, free, tutorial, map, phone, bri, ccnp

Article Source: http://www.articles2k.com

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage, home of free CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages.

You can also join his RSS feed and visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! Details are on the website.

For a FREE copy of his latest e-books, “How To Pass The CCNA” and “How To Pass The CCNP”, visit the website and download your free copies. You can also get FREE CCNA and CCNP exam questions every day! Get your CCNA study guide from The Bryant Advantage!

Top Computer Certification Articles
1). Cisco CCNA Certification Exam Tutorial: Variance And Unequal Cost Load Balancing By : Chris Bryant, CCIE #12933 To pass the CCNA exam, you've got to know how to work with IGRP and EIGRP unequal-cost load balancing. You may not see much IGRP in production networks anymore, but you'll see a lot of EIGRP, and part of fine-tuning your EIGRP network is making sure that all paths are in use while allowing for varying bandwidth rates. Using the variance command is the easy part - it's getting the metric that's the hard part with IGRP.
2). Cisco CCNA / CCNP Home Lab Tutorial: Configuring An Access Server By : Chris Bryant, CCIE #12933 As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we'll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS. Here's part of a configuration from one of my access servers: ip host FRS 2006 100.
3). Cisco CCNA Exam Tutorial: Route Summarization By : Chris Bryant, CCIE #12933 Preparing to pass the CCNA exam and earn this important Cisco certification? Route summarization is just one of the many skills you'll have to master in order to earn your CCNA. Whether it's RIP version 2, OSPF, or EIGRP, the CCNA exam will demand that you can flawlessly configure route summarization. Route summarization isn't just important for the CCNA exam.
4). Cisco CCNA Certification: Defining Broadcast Domains By : Chris Bryant, CCIE #12933 When you're studying to pass the CCNA exam and earn your certification, you're introduced to a great many terms that are either totally new to you or seem familiar, but you're not quite sure what they are. The term "broadcast domain" falls into the latter category for many CCNA candidates. A broadcast domain is simply the group of end hosts that will receive a broadcast sent out by a given host.
5). Cisco CCNP / BCMSN Exam Tutorial: Changing Root Bridge Election Results By : Chris Bryant, CCIE #12933 Your BCMSN and CCNP studies will include mastering the details of Spanning Tree Protocol (STP). While you learned some of these details in your CCNA studies, quite a bit of it may be new to you. Before going on to the intermediate and advanced STP features, let's review the root bridge election process and learn how to change these results. Each switch will have a Bridge ID Priority value, more commonly referred to as a BID.
6). How To Earn Cisco’s Firewall Specialist Certification By : Chris Bryant, CCIE #12933 Security is a hot topic in today's networks, and will continue to be for a long time to come. With that in mind, you must consider adding a Cisco security certification to your resume and firewall skills to your skill set. It's quite a jump from the CCNA to the CCSP (Cisco Certified Security Professional), and Cisco has made that leap more manageable by adding Specialist certifications.
7). Cisco CCNA Exam Tutorial: Configuring Standard Access Lists By : Chris Bryant, CCIE #12933 Access Control Lists (ACLs) allow a router to permit or deny packets based on a variety of criteria. The ACL is configured in global mode, but is applied at the interface level. An ACL does not take effect until it is expressly applied to an interface with the ip access-group command. Packets can be filtered as they enter or exit an interface. If a packet enters or exits an interface with an ACL applied, the packet is compared against the criteria of the ACL.
8). Cisco CCNP / BSCI Exam Tutorial: Using The OSPF Command “Area Range” By : Chris Bryant, CCIE #12933 Your BSCI and CCNP exam success depends on knowing the details, and one such detail is knowing the proper way to summarize routes in OSPF. Route summarization is not just a test of your binary conversion abilities, but knowing where and when to summarize routes. It will not surprise any CCNA or CCNP certification candidate that OSPF gives us the most options for route summarization, and therefore more details to know! OSPF offers us two options for route summarization configurations.
9). Cisco CCNP / BSCI Exam Tutorial: OSPF Route Redistribution Review By : Chris Bryant, CCIE #12933 OSPF route redistribution is an important topic on the BSCI exam, and it's a topic full of details and defaults that you need to know for the exam room and the job. To help you pass the BSCI exam, here's a quick review of some of the OSPF route redistribution basics. To see if a router is an ABR or ASBR, run show ip ospf. This also displays any routes being redistributed into OSPF on this router.
10). Passing Your CCNA and CCNP: Configuring And Troubleshooting Router-On-A-Stick By : Chris Bryant, CCIE #12933 For CCNA and CCNP candidates, it's hard not to laugh the first time you hear the phrase "router on a stick". Let's face it, that's a pretty silly term. But as those who have passed the CCNA and CCNP exams know, this is a vital exam topic that you must know how to configure and troubleshoot. Basic Cisco theory states that for hosts in different VLANs to communicate, a Layer 3 device must be involved to handle the routing between the VLANs.

New Computer Certification Articles
1). Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address By : Chris Bryant, CCIE #12933 To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial. We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is.
2). Cisco CCNP Certification / BSCI Exam Tutorial: An Introduction To BGP By : Chris Bryant, CCIE #12933 When you're studying for the BSCI exam on the way to earning your CCNP certification, it's safe to say that BGP is like nothing you’ve studied to this point. BGP is an external routing protocol used primarily by Internet Service Providers (ISPs). Unless you work for an ISP today or in the future, you may have little or no prior exposure to BGP. Understanding BGP is a great addition to your skill set – and you have to know the basics well to pass the BSCI exam.
3). Cisco CCNA Certification Exam Tutorial: Distance Vector Command Review By : Chris Bryant, CCIE #12933 Part of studying for CCNA exam success is keeping all these new commands straight in your head! And let's face it, there are a lot of commands you need to know in order to pass the CCNA exam and earn that certification. Here's a review of some very important distance vector and static routing commands you need to know, along with their proper usage and console output.
4). Cisco CCNA Certification Exam Tutorial: Keep Your Most Important Appointment By : Chris Bryant, CCIE #12933 Imagine this. You have an appointment with a client to work on a server or router install. A few minutes before you're scheduled to be there, you decide there's something really good on TV you'd like to watch. Or you decide to go to the gym, or play a game, or do anything else except go see the client. Even if you weren't going to get fired for not showing up, it's certainly unfair to the client.
5). CCNP Certification / BSCI Exam Tutorial: The BGP Neighbor Process By : Chris Bryant, CCIE #12933 Like TCP, BGP is connection-oriented. An underlying connection between two BGP speakers is established before any routing information is exchanged. This connection takes place on TCP port 179. As with EIGRP and OSPF, keepalive messages are sent out by the BGP speakers in order to keep this relationship alive. Once the connection is established, the BGP speakers exchange routes and synchronize their tables.
6). CCNP Certification / BCMSN Exam Tutorial: Server Load Balancing (SLB) By : Chris Bryant, CCIE #12933 When you're working on your BCMSN exam on your way to CCNP certification, you'll read at length about how Cisco routers and multilayer switches can work to provide router redundancy - but there's another helpful service, Server Load Balancing, that does the same for servers. While HSRP, VRRP, and CLBP all represent multiple physical routers to hosts as a single virtual router, SLB represents multiple physical servers to hosts as a single virtual server.
7). CCNA / MCSE / CCNP Certification: Making Failure Work For You By : Chris Bryant, CCIE #12933 Whether you're on the road to the CCNA, CCNP, MCSE, or you're on any other computer certification track, the odds are that sooner or later, you're going to fail an exam. It's happened to almost all of us, yours truly included. What you have to keep in mind in these times is that success is not a straight line. You've probably seen charts showing the growth of an industry or a business -- you know, the ones that go from left to right, and look kind of jagged.
8). Cisco CCNA / CCNP / BCMSN Exam Review: Trunking And Trunking Protocols By : Chris Bryant, CCIE #12933 To earn your CCNA or CCNP certification, you've got to understand the basics of trunking. This isn't just a CCNA topic - you must have an advanced understanding of trunking and etherchannels to pass the BCMSN exam and earn your CCNP as well. Before we address those advanced topics, though, you need to master the fundamentals! A trunk allows inter-VLAN traffic to flow between directly connected switches.
9). Cisco CCNP / BSCI Exam Tutorial: 10 ISIS Details You Must Know! By : Chris Bryant, CCIE #12933 Earning your CCNP certification and passing the BSCI exam depends on knowing the details of many Cisco technologies, ISIS chief among them. To help you prepare for exam success, here's a list of ISIS terminology and basic concepts that will help you pass this tough exam. Enjoy! ISIS Terms: Domain: section of the network under common administrative control Area: logical segment of the network composed of contiguous routers and their data links Intermediate System: A router.
10). Cisco CCNA / CCNP Certification Exam Tutorial: ISDN And Multilink PPP By : Chris Bryant, CCIE #12933 ISDN is a huge topic on both your Cisco CCNA and BCRAN CCNP exams. While many ISDN topics seem straightforward, it’s the details that make the difference in the exam room and working with ISDN in production networks. Configuring and troubleshooting multilink PPP is just one of the skills you’ll need to pass both of these demanding exams. With BRI, we've got two B-channels to carry data, and both of them have a 64-kbps capacity.